X-Powers Limited – All rights reserved. X-Powers. DATASHEET. Enhanced single Cell Li-Battery and Power System Management IC. AXP Page 2. VQ. AXP Datasheet, AXP PDF, AXP Data sheet, AXP manual, AXP pdf, AXP, datenblatt, Electronics AXP, alldatasheet, free, datasheet. AXP datasheet, AXP circuit, AXP data sheet: ETC2 – Enhanced single Cell Li-Battery and Power System Management IC,alldatasheet, datasheet.
|Published (Last):||26 January 2010|
|PDF File Size:||8.22 Mb|
|ePub File Size:||6.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
ADC sample rate settings, the TS pin control 8. M2M modules are also typically designed to operate off of a direct Lithium battery voltage and are not to be run off of a 3. This page was last modified on 2 Marchat Critical to be connected to the SoC. GPIO2 feature set datashet.
AXP Datasheet, PDF – Alldatasheet
Also as it is a UVC-video compliant device, linux kernel driver support is automatic. Note also in the example schematic that MMBT transistors have been deployed for simple level-shifting and also convenient inversion of the control signals.
The datasheet is incorrect here. For ultra-low-cost applications this is perfectly fine, considering the price and high availability. This module, it seems, is actually designed for use as a stand-alone, fully-functioning actual phone, not even requiring a companion SoC or MCU at all. V LTF-charge Charging the battery temperature threshold set 8. So to avoid cartel scenarios and also to avoid custom-ordering of minimum 10kk PMICsand to avoid the manufacturing and design complexity of re-programming the PMIC before it can be connected to the SoC, the best course of action is to analyse some available and extremely common PMICs, find out what their default outputs are, and then arrange the SoC and the Axp09 to be compatible with them rather than the other way round.
This example is included to show that power-provision can be done without a dedicated PMIC but also demonstrating quite how many components it actually needs, to datashdet so. Bear in mind that this all is a cooperative arrangement where the SoC and the PMIC must collaborate to prevent power-loss and current bun-fights.
Charging the end of the current set 0: To make that clear: LDO3 output voltage settings 8. This page has been accessed 68, times. GPIO0 feature set 8. The first bit is to enable or disable mask an interrupt, the second bit, 8 bytes later, is to indicate the interrupt state, e.
Corporations such as Intel have gotten themselves into a lot of trouble by supplying an SoC under NDA, then forgetting that it’s ultra-important to supply an easily-accessible PMIC that doesn’t additionally require a totally separate NDA just to gain access to it! It copes with up to around a 2A power provision. The clear Coulomb Counter control bit write Coulomb Counter will be cleared while this bit is cleared from.
Interrupt bank 5 8. Alternatives for higher power up to 4.
Example Reference Schematics for Peripherals
Interrupt bank 3 8. For an example implementation of this datasheeh see https: During aaxp209 operation, these modems, which are basically yet another ARM Processor and their own DDR and NAND storage with a full Software Stack often linux kernel based inside an enclosed metal box, are pretty much guaranteed to crash so hard that they become completely unrecoverable and unresponsive, and have even been known to cause the USB Host Endpoints that they are connected to to hard-crash as well. Only one modern USB chipset – which only supports Those caveats in mind: Control signals to the ES are: The OTG port is slightly different.
The Application Notes are significant which makes it an extremely good choice. Honestly it is simpler to just design the SoC to cope with the higher voltage. When the SoC detects that the inserted card has 1. LDO outputs – again controlled through I2C. Overall it is an extremely sophisticated PMIC which has the advantage of being mass-produced, proven just like the AXP before itand significant linux kernel driver support that is well-understood.
AXP209 Datasheet PDF
When an interrupt is fired and the interrupt line is pulled datashet, bit 7 of 0x48 will be set to 1. Without this integrated capacity to route power it actually becomes extremely hair-raising and requires something like 60 discrete components and Axo209 to replicate see jz reference schematics “LEPUS Board” for an example. ADC input range 8. This mode is entered either from pre-charge mode or constant current mode under certain conditions.
GPIO output low